manual, RUN/STOP, and alarms) and the PV or SV. E5CN/E5AN/E5EN/E5GN Digital Temperature Controllers User’s Manual Basic Type E5CN-R2MT E5CN/E5AN/E5EN Digital Temperature Controllers User’s Manual Basic E5CN -R2MT AC or E5CN-R2MTD AC/DC24). E5CN/E5CN-U Temperature Controller User’s Manual (Cat. No. H). E5CN Temperature Controller Communications User’s Manual (Cat. E5CN-R2MT-
|Published (Last):||12 January 2009|
|PDF File Size:||12.79 Mb|
|ePub File Size:||5.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
Easy, Dependable, Complete Functionality, and segment Displays.
Controllers now available with analog inputs. Faster sampling at ms.
Transfer output provided for easy output to recorders. Voltage outputs to drive SSRs for both heating and cooling control. Can be used for alarms to provide three alarm outputs. Models available with three-phase heater burnout detection and SSR fault detection. Easy setting with segment displays. Connect to either a thermocouple or platinum resistance thermometer with the same model. Easily see the status from a distance with PV display with threecolor switching function.
Setting protection indicator informs operator when protection is enabled. Controller available with long-life relay output available soon. Refer to Precautions on page Refer to page 19 for information on changes in comparison to previous models. Features Improved Functions for a Wider Range of Application Control Analog Values, such as Pressures, Flowrates, and Levels The new E5CN Series now also includes models that accept analog inputs, enabling control applications other than for temperature, including pressure, flowrate, level, humidity, and weight control.
Voltage outputs can be used for both heating and cooling for Models with Two Control Outputs. Also, control output 2 can be set for use as an alarm output, to enable using up to three alarm outputs. This enables the new E5CN to handle application requiring even greater response speed and accuracy. Three-phase Heater Burnout Detection With Models with Three-phase Heater Burnout and SSR Failure Detection, two current transformers can be connected to detect both heater burnout and SSR failure at the same time, reducing costs because a separate heater burnout alarm device is not required.
E5CN-C Models with Current Outputs Easy, Dependable, and Even Faster Easy Setting with segment Displays The new E5CN features segment displays to make text easier to read, eliminating the need to decode displays when trying to set parameters, as was necessary with previous temperature controllers. Multi-input Capability with One Controller Connect to either a thermocouple or platinum resistance thermometer with the same model. Model selection is simplified, stocks are reduced, and fewer maintenance parts are required.
Voltage for driving SSR C: Long-life relay output available soon 2. Number of alarms Blank: Option Unit can be mounted 4. Analog input This data sheet is provided as a guideline for selecting products.
Be sure to refer to the following user manuals for application precautions and other information required for operation before attempting to use the product. Option Units e5cn-r2mt500 be used for Plug-in models. Do not 14 use.
EUROTHERM ERO LFS Controller PID Heater Break Alarm Rs W/ Manual Hardware | eBay
Do not 15 5ecn-r2mt-500. Use this Adapter when the panel has been previously prepared for the E5B. Pt or JPt Infrared temperature sensor: IEC Shaded settings are the default settings. Case 1 and 2 Always OFF when the upper-limit and lower-limit hysteresis overlaps. Set the alarm types for alarms 1 to 3 independently in the initial setting level. The default setting is 2 upper limit.
The baud rate, data bit length, stop bit length, and vertical parity can be individually set using the Communications Setting Level. Equivalent to IP50, rear case: IP00 Non-volatile memory number of writes: When robust tuning RT is ON, the differential time is e5cj-r2mt-500. B, R, and S sensors: Minimum detection ON time: Mznual failure detection alarm manuap range 0. Minimum detection OFF time: If the ON time of control output 1 is less than ms, heater burnout detection and the heater current will not be measured.
If the OFF time of control output 1 is less than ms, SSR failure detection and the heater current will not be measured. A voltage output control output is not electrically insulated from the internal circuits. When using a grounding thermocouple, do not connect any of the control output terminals to ground.
OMRON E5CN Datasheet: Ordering Information
If the control output terminals are connected to ground, errors will occur in the measured temperature values as a result of leakage current. Standard insulation is applied between any of the following: If reinforced insulation is required, provide additional insulation, such as spacial distance or material insulation, as defined by IEC suitable manua the maximum operating voltage.
Output when an input error output is enabled in the Advance Function Setting Level. If an input error output is enabled, the a operation indication on the front panel will not light and s.
Terminal applications depend on the model of the Option Unit.
If an input error output is enabled, the al-1 operation indication on the front panel will not light and s. Group mounting does not allow waterproofing. Recommended panel thickness is 1 to 5 mm. Group mounting is not possible in the vertical direction. Maintain the specified mounting space between Controllers. To mount the Controller so that it is waterproof, insert the waterproof packing onto the Controller. When two or more Controllers are mounted, make sure that the surrounding temperature does not exceed the allowable operating temperature specified in the specifications.
Plug Two, M3 depth: Use this Adapter when the panel has already been prepared for the E5B. Can also be mounted to a DIN track. A model with finger protection P2CFE is also available.
Back-connecting Socket P3GA 27 dia. Using any other sockets will adversely affect accuracy. Use only the specified sockets. A password is required to enter the advance function setting level and the calibration level. Some parameters may not be displayed depending on the protection mxnual and operation conditions.
Ordering Information – Omron E5CN Datasheet [Page 3]
The control operation will stop when switching from operation level to initial setting level. Press the Level Key See for at least 3 s while note 3. Press the Level Key for at least 3 s. Protect Level Press the Level Key for at least 1 s.
Set value See note 2. Operation level entered for software reset. You cannot move to other levels by operating the keys on the front panel from the calibration level. You must turn OFF the power supply. You can move only to the operation level by operating the keys on the front panel from the manual control level. H Manula the Level Key for at least 3 s. Display flashes for at least 1 s.
Starting manial automatic mode Press the Level Key less than 1 s. Adjustment Level Press the Level Key less than 1 s. Operation Level Set either of these parameters. Set either of these parameters. C al1l Lower-limit 1 alarm value 0 a 40 a ct1 Heater current value 1 0.
Press the Level Key less than 1 s. SP used by multi-SP Protect Level The time taken to move to the protect level can be adjusted e5cn-t2mt-500 changing the “Move to protect level time” setting. Communications Setting Level Displayed only for models with communications. Changes are effective after cycling power or after a software reset. C sp-2 SP 2 0 a ol-h MV upper limit The input type e5cn-r2mh-500 numbers have changed to allow for e5ch-r2mt-500 specifications.
EUROTHERM ERO LFS Controller PID Heater Break Alarm Rs485 W/ Manual Hardware
Previous E5CN Controllers cannot be removed from the case for replacement with new models. Replace the case at the same time. The e5cn-r2mt-500 ThermoTools cannot be used with the new Controller models. Use the ThermoTools scheduled for marketing from July The height of the front panel that extends when the Controller is mounted to a panel has been reduced from 9 to 6 mm.
Panel interior dimensions for panel mounting?